Bostitch F21PL User Manual Page 14
- Page / 40
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14
TROUBLE SHOOTING
P
ROBLEM
C
AUSE
C
ORRECTION
T
rigger valve housing leaks air O-ring cut or cracked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-ring
Trigger valve stem leaks air O-ring/seals cut or cracked . . . . . . . . . . . . . . . . . . . . . . . . . .Replace trigger valve assembly
Frame/nose leaks air Loose nose screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten and recheck
O
-ring or Gasket is cut or cracked . . . . . . . . . . . . . . . . . . . .Replace O-ring or gasket
Bumper cracked/worn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace bumper
Frame/cap leaks air Damaged gasket or seal . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace gasket or seal
C
racked/worn head valve bumper . . . . . . . . . . . . . . . . . . . . .Replace bumper
Loose cap screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten and recheck
F
ailure to cycle Air supply restriction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply equipment
Tool dry, lack of lubrication . . . . . . . . . . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
Worn head valve O-rings . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-rings
B
roken cylinder cap spring . . . . . . . . . . . . . . . . . . . . . . . . . .Replace cylinder cap spring
Head valve stuck in cap . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassemble/Check/Lubricate
Lack of power; slow to cycle Tool dry, lacks lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
B
roken cylinder cap spring . . . . . . . . . . . . . . . . . . . . . . . . . .Replace cap spring
O
-rings/seals cut or cracked . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-rings/seals
E
xhaust blocked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check bumper, head valve spring, muffler
Trigger assembly worn/leaks . . . . . . . . . . . . . . . . . . . . . . . . .Replace trigger assembly
Dirt/tar build up on driver . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassemble nose/driver to clean
C
ylinder sleeve not seated correctly on bottom bumper . . . .Disassemble to correct
Head valve dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassemble/lubricate
Air pressure too low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply equipment
Skipping fasteners; intermittent feed Worn bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace bumper
Tar/dirt in driver channel . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassemble and clean nose and driver
Air restriction/inadequate air flow through
quick disconnect socket and plug . . . . . . . . . . . . . . . . . . . . .Replace quick disconnect fittings
Worn piston O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-ring, check driver
Tool dry, lacks lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
Damaged pusher spring . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace spring
Low air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply system to tool
Loose magazine nose screws . . . . . . . . . . . . . . . . . . . . . . . .Tighten all screws
Fasteners too short for tool . . . . . . . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners
Bent fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners
Wrong size fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners
Leaking head cap gasket . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten screws/replace gasket
Trigger valve O-ring cut/worn . . . . . . . . . . . . . . . . . . . . . . . .Replace O-ring
Broken/chipped driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace driver (check piston O-ring)
Dry/dirty magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Clean/lubricate use BOSTITCH Air Tool Lubricant
Worn magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace magazine
Fasteners jam in tool Driver channel worn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace nose
Wrong size fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners
Bent fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners
Loose magazine/nose screws . . . . . . . . . . . . . . . . . . . . . . . .Tighten all screws
Broken/chipped driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace driver
Fastener misses Broken / chipped guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace guide
metal connector hole Broken / missing 158457 torsion spring . . . . . . . . . . . . . . . .Replace torsion spring (grease before installation)
(For F21PL, F33PT) Broken Pendulum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace pendulum and torsion spring
Broken 158455 pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replace pin and torsion spring
- F21PL / F21PL2 / F28WW 1
- F33PT / F33PTSM 1
- INTRODUCTION 2
- SAFETY INSTRUCTIONS 3
- AIR SUPPLY AND CONNECTIONS 3
- LOADING TOOL 3
- OPERATION 3
- MAINTAINING THE TOOL 3
- F SERIESTOOL SPECIFICATIONS 4
- OPERATION (continued) 5
- LUBRICATION 5
- LOADING THE F SERIES TOOLS 6
- DIRECTIONAL EXHAUST DEFLECTOR 7
- REMOVING NAILS 7
- PULL BACK ON PAWL 7
- TO RELEASE NAIL STICK 7
- TOOL OPERATION 9
- TOOL OPERATION (CONTINUED) 10
- SEQUENTIAL TRIP 11
- TOOL OPERATION CHECK: 12
- REPLACEMENT PARTS: 13
- ASSEMBLY PROCEDURE FOR SEALS: 13
- INTRODUCCIÓN 15
- SECUENCIAL DE CONTACTO 18
- ATILLO GRIS GATILLO NEGRO 18
- DISPARO DISPARO 18
- F21PL2,Y F33PT, F33PTSM: 19
- VIEW 3 PAGE 7 20
- Figura 1 21
- Figura 2 21
- FUNCIONAMIENTO 22
- ADITAMENTO CONECTOR DE METAL 24
- PIEZAS DE REPUESTO: 26
- PROBLEMA CAUSA CORRECCIÓN 27
- REMARQUE : 28
- CONSIGNES DE SÉCURITÉ 29
- CHARGEMENT DE L’APPAREIL 29
- FONCTIONNEMENT 29
- ET F33PT ET F33PTSM : 32
- Figure 1 34
- Figure 2 34
- FONCTIONNEMENT DE L’OUTIL 35
- UTILISATION 35
- DÉCLENCHEUR SÉQUENTIEL 37
- PIÈCES DE RECHANGE : 39
- PROBLÈME CAUSE SOLUTION 40
Related products and manuals for Staple guns Bostitch F21PL
Staple guns Bostitch BTFP12182 User Manual
(22 pages)
(22 pages)
Staple guns Bostitch N80CB Specifications
(31 pages)
(31 pages)
Staple guns Bostitch SB-100SX User Manual
(70 pages)
(70 pages)
Staple guns Bostitch 600 SERIES User Manual
(20 pages)
(20 pages)
Staple guns Bostitch SB-100SX Specifications
(30 pages)
(30 pages)
Staple guns Bostitch EHF1838K Specifications
(34 pages)
(34 pages)
Staple guns Bostitch D61ADCSB User Manual
(10 pages)
(10 pages)
Staple guns Bostitch PC5000 Specifications
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.843 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals