N52FN/N62FNINDUSTRIAL OIL FREE ANGLED FINISH NAILERSCLAVADORA INDUSTRIAL EN BARRA ANGULA LIBRE DE LUBRICACIÓNCLOUEURS INDUSTRIEL DE FINITION EN BANDES
Trigger valve housing leaks air O-ring cut or cracked . . . . . . . . . . . . . . .Replace O-ringTrigger valve stem leaks air O-ring/seals cut or c
-11-MAINTAINING THE PNEUMATIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.CAUTION:Pus
INTRODUCCIÓNLa N52FN/N62FN de Bostitch es una herramienta fabricada con precisión diseñada para trabajos de clavarde alta velocidad y de gran volumen.
INSTRUCCIONES DE SEGURIDADCuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas quese encuentren en el área
-14-ESPECIFICACIONES DE LAS N52FN/N62FNTodos las medidas de tornillos y tuercas son métricas.ESPECIFICACIONES DEL SUJETADOR:CONEXIÓN DE AIRE DE LA HER
-15-SUMINISTRO DE AIRE Y CONEXIONESNo use oxígeno, gases combustibles o gases embotellados como una fuente de suministro para esta herramienta, ya que
-16-CARGA DE LAS HERRAMIENTAS N52FN/N62FNCuando el equipo está conectado al suministro de aire, tanto el operador como todas laspersonas que se encuen
-17-OPERACIÓN DE LA HERRAMIENTACuando el equipo está conectado al suministro de aire, tanto el operador como todas laspersonas que se encuentren en el
-18-VERIFICACIÓN DE LA OPERACIÓN DE LA HERRAMIENTA:¡PRECAUCIÓN: QUITE TODOS LOS SUJETADORES DE LA HERRAMIENTA ANTES DE EFECTUAR LA VERIFICACIÓN DE LA
-19-El Ajuste del Control de Fondo del Sujetador DIAL-A-DEPTH permite controlar minuciosamente el fondo deimpulsión del sujetador, desde a ras con o j
-2-INTRODUCTIONThe Bostitch N52FN/N62FN series nailers are precision-built tools, designed for precise high volumenailing.These tools will deliver eff
-20-DIAGNÓSTICO DE FALLAPROBLEMA CAUSA CORRECCIÓNFuga de aire en la envoltura de la ...Anillo en O cortado o rajado . . . .
-21-MANTENIMIENTO DE LA HERRAMIENTA NEUMÁTICAAl trabajar con herramientas neumáticas, tenga presente las advertencias que se hacen en este manual, y s
-22-INTRODUCTIONLe N52FN/N62FN de Bostitch est un outil construit avec précision; conçu pour réaliser un travail rapide à débitmaximum. Les cloueurs s
ENTRETIEN DE L’APPAREILLors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissements dumanuel et user d’extrêmes précautions lo
CARACTÉRISTIQUES DES N52FN ET N62FNToutes les mesures des vis et des boulons sont dans le système métrique. CARACTÉRISTIQUES DES ÉLÉMENTS D’ASSEMBLAGE
-25-ALIMENTATION EN AIR COMPRIMÉ ET RACCORDEMENTL’oxygène, les gaz combustibles ou les bouteilles de gaz ne doivent en aucun cas êtreemployés comme so
CHARGEMENT DU N52FN OU DU N62FNUNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protectioncontre les projectiles en provenance de
FONCTIONNEMENT DE L’APPAREIL UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protectioncontre les projectiles en provenance de l’
-28-VÉRIFICATION DU SYSTÈME DE DÉCLENCHEMENT :ATTENTION : retirer toutes les attaches de fixation de l’outil avant de procéder à une vérification dufo
-29-Le réglage de la profondeur de l’élémentd’assemblage DIAL-A-DEPTH permet d’obtenir uncontrôle précis de la profondeur de clouage; depuisle clouage
-3-SAFETY INSTRUCTIONSEYE PROTECTION which conforms to ANSI specifications and provides protection againstflying particles both from the FRONT and SID
-30-PROBLÈMES DE FONCTIONNEMENTPROBLÈME CAUSE CORRECTIONFuite d’air au corps de valve de détente. . . . . . . . . Joints toriques coupés ou usés. . .
-31-ENTRETIEN DE L’APPAREILLors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissementsdu manuel et user d’extrêmes précaution
All screws and nuts are metric.FASTENER SPECIFICATIONS:TOOLAIR FITTING:This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .200” (5
AIR SUPPLY AND CONNECTIONSDo not use oxygen, combustible gases, or bottled gases as a power source for thistool as tool may explode, possibly causing
-6-EYE PROTECTION which conforms to ANSI specifications and provides protection againstflying particles both from the FRONT and SIDE should ALWAYS be
1. TRIGGER OPERATIONThe TRIGGER OPERATED tool requires a single action to drive a fastener. Each time the trigger is pulledthe tool will drive a faste
TOOL OPERATION CHECK:CAUTION: Remove all fasteners from tool before performing tool operation check.1. TRIGGER OPERATED TOOL:A. With finger off the tr
-9-The DIAL-A-DEPTH™Fastener Control adjustmentfeature provides close control of the fastener drivedepth; from flush with the work surface to shallow
Comments to this Manuals